Vaphit HX Vaporizer

The Vaphit HX - New for 2025.

The HX offers a new experience, Quartz and Glass airpath and cap, stainless steel tip. It's a bit like putting a DynaVap tip into a Vaphit QoQ.
It's like a QoQ but with a faster heat up, and slightly longer heat retention - offering extended sessions from a single heat up cycle. A great piece to add to your Vaphit collection.
The Vaphit HX uses the same extra deep tip that is found in Vaphit X kits, and is interchangeable with any 8mm tip from various brands.

The HX comes packaged in a neat Vaphit branded carry case, with a load of accessories to keep you going. Straight out of the box you have 1.5mm and a 1.0mm thickness Quartz Cap, cleaning accessories, a whole host of o-rings, and the best part of all - the 14mm Male WPA. The WPA allows you to use the HX paired with your favourite 14mm water pipes. Be sure to try this out!

Usage:
Simply load the tip, slide the cap on and you are ready to heat.
The heating of the Vaphit HX is similar to other Vaphit Quartz devices. Preferably you want to opt for a medium torch. From testing we found that depending on flame size you can get optimal vapor production from about 10-20 seconds heating. Simply torch above the caps vent holes - around the area your material sits, and spin the device in hand for even heating, when the flame hitting the Quartz turns from blue to yellow its about time to inhale. You can also see the material begin to change colour. Usually as soon as you begin to see slight darkening is when it is ready to be inhaled. You can repeat the heating process a few times, as you begin to see the vapour decrease.
Once done and it's time to reload, ensure you slide the cap off using the silicone grippers - the cap will be very hot.

The capacity is around about a maximum of 0.1g of finely ground material. You don't want to put too much in or tamp it down hard, this will restrict airflow. Less is sometimes better. Try doing a "straw-pack" where you inhale through one end with the tip placed into your material, this will give you a light pack that will give you amazing airflow.

Cleaning:
Cleaning your Vaphit HX is a breeze, break down the device, removing all o-rings and simply soak glass and Quartz pieces in 70%+ Isopropyl Alcohol. Ensure you thoroughly rinse it clean after.

• 1x Vaphit Glass Helix Mouthpiece with 316L Stainless Steel Adapter
• 1x 316 Stainless Steel X Bowl with 6 Mini Holes
• 1x Vaphit Carrying Case
• 1x 304 Stainless Steel Stick for Loading and Removing Screen
  
• 1x Silicone Heatproof Finger Protector for Removing Quartz Cap
  
• 1x 1.5mm Thickness Long Quartz Heating Cap with 1.5mm Holes
  
• 1x 1.0mm Thickness Long Quartz Heating Cap with 1.5mm Holes       
• 1x 14mm Male Joint WPA
  
• 1x 5-PACK of 304 Stainless Steel Screens
  
• 1x 10-PACK of 6.5mm*1.2mm O-Rings
  
• 1x 10-PACK of 7.0mm*1.2mm O-Rings
  
• 1x 10-PACK of 7.5mm*1.2mm O-Rings
  
• 1x 10-PACK of 8.9mm*1.2mm O-Rings
  
• 1x10-PACK of 9.5mm*1.2mm O-Rings
  
• 1x 10-PACK of 10mm*1.2mm O-Rings
  
• 1x 10-PACK of 15mm*1.2mm O-Rings (For Helix Mouthpiece)
  
• 1x Stainless Steel Tweezers for Loading O-rings